Heads

#1031-012
ROTOR HEAD FULL SET
FOR SHUTTLE 30

It uses seesaw type which is better than 60 Heli in flight stability and maintenance. It will bring flight fully into play and will enhance flight stability in 3D flight and back-hovering.

#1031-013
SEESAW HEAD FOR SHUTTLE 30

This product adapts seesaw type which is used for the main type 60 Heli. It helps to get the best effect for 3D flight, hovering and all-round. It can go with both shuttle normal blade holder and ARK blade holder.

#1031-056
DFH-320 FLAPPING ROTOR HEAD
FOR SHUTTLE 30

It's equipped with 2 individual feather ring spindle at two sides and one UF stabilizer, so when pitch can't return to the origin, it has the function of flapping head. When pitch is operated, it becomes rigid-type
function so operated, it features linear smoothness.
NOTE: Ball bearing not included. (Ball bearing
attached to the kit can be used instead.)

#1031-059
SD-320 ROTOR HEAD (Flapping-Type)
FOR SHUTTLE 30

#1031-018
HEAD CONVERSION SET
FOR SHUTTLE 30

#1031-029
BLADE HOLDER FOR SHUTTLE 30

Both shuttle normal head and ARK head are changeable. It is made of reliable aluminium alloy and is safe during 3D flight. Bearing is attached, but pitch arm is not included.

#1031-044
SWASH PLATE ( 8mm )
FOR SHUTTLE 30

#1041-003
SWASH PLATE GPH346 ( 10mm )
FOR GPH346

#1031-031
CONTROL ARM

Made of anodized aluminum alloy which is very precise (the set doesn't include bearing).

#1031-008
CONTROL ARM (W/OUT BEARING)

#1031-033
MIXING ARM (W/BEARING)

#1031-034
WASH OUT ARM (W/BEARING)

#1031-022
WASH OUT ARM

#1031-24
WASH OUT LOCK

#1031-010
MIXING ARM

#1031-028
PITCH ARM

#5203-041
STABILIZER SEESAW

This is cut by CNC and is made of Aluminum alloy, which is precise, strong and light.

#5203-042
WASH OUT BASE

The wash out is cut from aluminum alloy. Because there is metal on the slide of mast, the movement will be very smooth.

#5203-043
STABILIZER CONTROL ARM

The angle of ball ring differs from normal products for 90. When doing a big angle movement, there won't be ball ring lock. It is made of stainless steel which is very strong.

#1041-001
SP MIXING ARM

The new SP MIXING ARM has improved its lever ratio. There is an additional install hole which is 2.5 m/m away from the standard hole. It is suitable for both beginners and experts. It enables the pitch to keep its degree accurately from positive 14°to negative 13°
especially for stunt, 3D flight. (The product is made of
aluminum and is cut by CNC in one piece. It is red and
is processed by Alumite.)

#1041-201
BIG HEAD TOP DOME FOR GPH346

#1031-040
NOR HEAD TOP DOME

Top Dome is used to reduce wind resistance and to be the brake as stops. It can be assembled in shuttle normal head just with one touch.

#0401-054
PITCH ARM
FOR SHUTTLE 30 (ARK HEAD)

#0403-053
PIVOT SET
FOR SHUTTLE 30 (ARK HEAD)

#0404-053
SPINDLE SET
FOR SHUTTLE 30 (ARK HEAD)

#0405-012
CENTER DAMPER
FOR SHUTTLE 30 (ARK HEAD)

#0405-014
SPINDLE COLLAR
FOR SHUTTLE 30 (ARK HEAD)

#0405-015
PIVOT SET
FOR SHUTTLE 30 (ARK HEAD)

#0405-016
YOKE SIDE PLATE (WITH Brg.& COLLAR)
FOR SHUTTLE 30 (ARK HEAD)

#0405-019
FEATHERING BLOCK
FOR SHUTTLE 30 (ARK HEAD)

#0405-053
UF STABILIZER

#0406-053
THRUST COLLAR SET

#1031-005
MAIN MAST

#1031-014
STABILIZER BAR

#1031-015
FEATHERING SPINDLE

#5203-068
CENTER HUB
FOR SHUTTLE 30 (ARK HEAD)

#5203-322
SPINDLE SHAFT

#5401-090
PIVOT BOLT (4pcs)

#5401-091
PIVOT BOLT(6pcs)

#5401-093
PITCH LEVER SET (2pcs)
FOR SHUTTLE 30 (ARK HEAD)

#5600-018
4.6mm LINKAGE BALL(10pcs)

#5600-110
FLANGE BEARING 3*6*2.5(4pcs)

#5600-113
FLANGE BEARING 3*8*3(2pcs)

#5600-115
FLANGE BEARING 5*11*5

#1034-001
FLANGE BEARING 5x10x4 (2pcs)

#5801-011
3*4.5*0.5mm WASHER (10pcs)

Upgrade Parts of SHUTTLE ZX

1031-019 BATTERY MOUNT
Fitted forward in the airframe this allows for battery position adjustment providing longitudinal balance of the helicopter.